![]() |
|
Политика Экономика Проиcшествия Общество Спорт Культура и искусство Знаменитости Наука и технологии Авто Интернет Женские советы Питание Обустройство дома Строительство ![]() Лента свежих новостей 06 мая. | 19:50
Що потрібно знати про морські контейнерні перевезення 05 мая. | 10:35
Українські ставки на спорт: переваги та правила 01 мая. | 19:03
Как правильно выбрать курс процедур для коррекции контуров тела 01 мая. | 19:01
Що включає підготовка до вакцинації та основні правила 01 мая. | 18:58
Стоматологический гель: достоинства применения в стоматологии 01 мая. | 06:58
Обида на родителей: как справиться с этим 29 апр. | 15:49
Как устроено онлайн-казино и его достоинства 28 апр. | 06:44
Как выбирать парик из натуральных волос и несколько советов 23 апр. | 19:04
FineReader: революция в обработке текстов и документов 23 апр. | 06:18
Как подавать на алименты в Украине и несколько советов |
How to repair the underlying lamb in the trunk: Stages
How to repair the underlying lamb in the trunk: Stages Finally, my hands reached the false trunk with a hatchet for a spare. Although there are topics on third -party resources, I decided to share with the participants of my favorite club. Photo report: first I wanted to cut the plywood on the drawing placed on the drive2, but the sizes indicated there were small, it would be large, no, a huge gap around the perimeter. As a pattern used? native? The felt of the former owner: by cutting down the contour began to "adjust the measurements on the spot". Here there were big problems, the plywood did not want to climb into the trunk, but "one head is good, two - better", thanks to Kolyan, took off the side casing in the trunk: P. S.: The workpiece did not want to climb, I had to shoot about 1.5 cm around the perimeter, as a result of which I achieved that the plywood was inherent in the trunk with minimal resistance. The lower photo shows the finished plywood for gluing carpet. * screwed the loops in advance to hide them under the carpet.*on the sides of the cut, screwed pieces of plywood to support the hatch, for the flatness of the floor, and to increase the loads of resistance. In the photo below the already glued plywood. Not yet glued hatch. Yes.... Crookedly, the hatch cut off, the innocent I... This is a jigsaw on the guys are a broken -down, and a laminate canvas, and not for plywood. Well, and in general, the result: spent: a sheet of plywood 8mm, moisture -resistant - 400 rubles. by blat (spent exactly half of the sheet, t. e. From one standard (1250x1250mm) you can make 2 false sex) carpet 2m. - 600 rub. (300 rubles each./meter, took 2 mtra, just in case, and to glue the hatch on both sides) loops 2 pcs. - 44 rub. (22 rubles. in castrama) a brush 63 mm wide - I don’t remember how many, in my opinion, about 40 rubles. In Castorama. Glue universal moment 750 ml. - Bank - 200 rubles. In Castorama. Total: about 1500 rubles., Wild desire to do awesomely cool, three posts of work evenings, and... frantic high from the result. P. S.: I bought all of the above, threw it into the car,, at our heat at 34 degrees, in general, the bank with glue rushed, and all the glue dragged on, it is good that everything was in the castorama package, the seat was not injured, but it had not been dried up until it dried up glue, cleanse the loops, and the pile of the brush was in cellophane, in general, nothing disappeared except glue, but the guys smokes the cheeks shared glue, even more, we need half the cans there. Now I am not ashamed to open the trunk, all superfluous is hidden from the eyes, everything is exactly and purely. Jamb: in view of not the absolute evenness of the body, from below the false noise is about 1-2 cm. Поделись с друзьями:
Похожие публикации
|